The advantages of the FELDER quick change spindle system: Easy, quick change of the spindle; ability to use 25, 30, 40, 50 mm, ¾’’ and 1 ¼’’ diameter spindles; high speed router spindle for router bits with 15,000 rpm; automatic repeatable setting for production work.

With a completely new design, the Felder “700” ­spindle unit sets new standards!
4½” (115 mm) under the nut capacity
Table opening: 9” (230 mm)
Quick change system for shaper spindle
4 operating speeds (3500, 6500, 8000, 10,000 rpm)
Speed changes are done from the front of the machine
Fully compatible with high speed router spindle at 15,000 rpm
Tilts backwards 0° to 45°
Electrical height adjustment with LED display
Precise double trunnion system
Dovetail guidance system for height adjustment
Maximum motor power transfer with the Poly-V belt
Excellent vibration absorption from heavy cast iron unit
Tilt segment “Easy-Glide”:
- High durability
- Play free tilt
- Unaffected by dust
- Completely maintenance free
- No lubrication required

The high speed router spindle is designed for router shaft diameters of Ø ¼” – ⅝”
(6–16 mm) and a speed of 15,000 rpm.

All Felder shapers have standard equipment including a tilting shaper spindle 90°–45°. Due to the tilting shaper spindle, the range of applications and savings of tooling cost may be much higher than you have expected. Using the handwheel causes the whole shaper spindle unit to tilt to the desired angle easily and smoothly.

The dual dust extraction for shaper via the shaper fence and the chip collecting bin under the cutter ensure that the machine remains clean and good working results are obtained.

Accurate tenons are much easier with the Felder “X-Roll” sliding table. This precision guiding system will accept maximum loads without compromising the smooth and accurate stroke of the sliding table. The “X” configuration of the roller bearings optimally distributes work-piece weight to all sides. With conventional sliding tables, ball bearings are used in the guiding system. A ball bearing system creates a singular point of contact between the bearings and the flat guiding tracks. The “singular point contact” will eventually wear grooves into the tracks and as a result, sideways play will develop in the sliding table. It is physically impossible for the “X-Roll” system (with roller bearing lineal contact) to wear grooves into the guiding tracks, hence the system will allways remain play-free and is backed with a 6 year
factory warranty.

The ”240“ shaper fence is standard equipment on the shaper units. The shaper fence can accomodate tooling to a maximum of 9“
(230 mm) and has a micro-adjustment on the shaper fence outfeed side. The integrated dust extraction cowling allows for chip removal. The spindle table opening is 9“ (230 mm). This allows the spindle with the cutterhead attached to be lowered below the table in some cases.

The MULTI fine adjustment system allows quick adjustment of the work piece diameter, allowing parallel guidance of the shaper fence.
- Automatic repeat setting after removal of your fence
- Parallel adjustments of the shaper fence
- Fence can be pre-set to a desired position
- Measurement scale for depth of cut

Optimize your cut­ting speed to suit each and every job. Infinitely variable speed control, from 1500–11,000 rpm.

The safety bar guides, great for “end-grain” work (optional).

Hardened anodized aluminum fence plates are standard. Precise, fine adjustment on the remov­able shaper fence via a scale from –.4” to +1.38” (–10 to 35 mm).

The large table opening allows for maximum operator safety. For large dimension tooling, as used for tennoning and panel raising, the cutter can be conveniently positioned below the table.

An optional outrigger table can be added to your sliding table (2000 mm/78” table required). With this valu­able option, you can easily work with large work pieces e.g. Rebate a door with ease and precision.