With an 3½” diameter (88 mm) knife cutting radius, knife cutter block and the unique Felder system cutterblock technology, the Felder jointing result reaches new heights.
Fifteen years ago, Felder introduced the double sided disposable planer knife system. After each cutterblock knife change, start again with perfectly adjusted machine edged planer knives. Its much faster and more economical than the traditional systems.

Its mere child’s play to change the planer knives. In less than a few minutes you can change either the 4 knife cutterblock. Felder planer knives are instantly ready for action!

Constructed completely out of cast iron, the new Felder 700 Series saw unit represents a new era of running stability and efficiency.
4" cutting height with a 315 mm (12") saw blade
Dado capability up to ¾” (19.5 mm)
Electrical height adjustment with LED display
Zero point tilt
Oversized saw arbor with double bearing seats
Maximum motor power transfer with the Poly-V belt
Optimal extraction with the completely enclosed, below table extraction system
Precise height adjustment via precision linear guides
Precise double trunnion system
Tilt segment “Easy-Glide”:
- High durability
- Play free tilt
- Unaffected by dust
- Completely maintenance free
- No lubrication required

The electronically balanced saw arbor with dual bearing seat system is powered via a Poly-V belt. Combined this results in an almost perfect transmission of power to the saw blade.

The Felder 700 Series saw assembly is fully compatible with dado tooling. Thanks to removable flanges and table insert, the Felder designed, fully adjustable dado cutters can be used.

Continuous fence for ripping: Any dimension is possible: the fence will always be fixed in a position parallel to the sawblade. You’ll always have the best possible work surface.

The advantages of the FELDER quick change spindle system: Easy, quick change of the spindle; ability to use 25, 30, 40, 50 mm, ¾’’ and 1 ¼’’ diameter spindles; high speed router spindle for router bits with 15,000 rpm; automatic repeatable setting for production work.

Annoyed setting up and removing the power feeder? Not with a Felder! You can leave your power feeder permanently mounted to your Felder and easily tilt it out of the way when not in use.

Easy mortising: Operation with one hand by a lever and safe clamping of any work piece with an eccentric clamp.

4 Spindles with trapezoidal threads guarantee precise adjustment and allow the heaviest loads on the planer table. The table height adjustment guideways (A + B) also stabilize the table against lateral movement particularly in the outfeed ­direction.

The crosscut fence is 43” (1100 mm) for crosscuts between +45° and –45°. The fence can be attached to the sliding table with out the use of tools. The positive stop provides you with the exact 90° position.
The bevelled miter scale with hairline readout is visible from the operating area and thus allows exact reading of the required crosscut value.
The large crosscut fence stops are constructed in such a way that a small tongue on the stop fits perfectly into a groove on the fence. This means the crosscut fence stop remains firmly in place, especially useful when crosscutting pre-­mitered workpieces.

The 102” (2600 mm) long telescopic crosscut fence can be effortlessly adjusted from 90° to 45°. A miter scale on the outrigger table allows for accurate adjustments. On request we will fit your outrigger table with the precision miter pin locating system. Locate your miter angles accurately time and again!

Precise and comfortable quick adjustment of cutting depth from the operator side of the infeed table.

Precise adjustment. This is obtained with the patented jointer table adjusting system that works in positive union with lateral prismatic guide ways.

It is easy to change quickly from jointer to planer on your machine. 4 tension springs on each table help to raise the jointer tables.

Planing accuracy to .001“ with the use of a handwheel and with intergrated digital display. Max. planing height 9⅞” (250 mm).

Due to its extremely good design and large dimension, the dust extraction hood is very efficient.

Turn the control switch for quick adjustment, fine adjustment with the push of a button. The LED display clearly shows the planer table position.

Enter required dimension, press start and the planer table will move accurately to the required position. Required and actual values are shown on LED displays. Additional functions: incremental function and 4 programmable planer table positions.

The scoring unit for cuttings in plastic laminated panels and two-sided veneers without tear-outs. Backlash-free height and lateral adjustment of the scoring saw blade. Drive power of the industrial scoring unit 1.0 HP.

The Felder precision sliding table has been designed to accept maximum loads while also remaining smooth running and accurate. The monoprofile of the sliding table and base guarantees maximum torsional strength at every temperature. Through the “X” positioning of the roller bearings the pressure load is optimally distributed to all sides. The “X-Roll” guiding system and the other numerous outstanding details will be patented to ensure their protection. So much precision and technology earns the right to the status of “World Class”.

With a completely new design, the Felder “700” ­spindle unit sets new standards!
4½” (115 mm) under the nut capacity
Table opening: 9” (230 mm)
Quick change system for shaper spindle
4 operating speeds (3500, 6500, 8000, 10,000 rpm)
Speed changes are done from the front of the machine
Fully compatible with high speed router spindle at 15,000 rpm
Tilts backwards 0° to 45°
Electrical height adjustment with LED display
Precise double trunnion system
Dovetail guidance system for height adjustment
Maximum motor power transfer with the Poly-V belt
Excellent vibration absorption from heavy cast iron unit
Tilt segment “Easy-Glide”:
- High durability
- Play free tilt
- Unaffected by dust
- Completely maintenance free
- No lubrication required

The high speed router spindle is designed for router shaft diameters of Ø ¼” – ⅝”
(6–16 mm) and a speed of 15,000 rpm.

The tilting segment on the Felder 700 series has one small but important detail: it is completely free of lubrication!

All Felder shapers have standard equipment including a tilting shaper spindle 90°–45°. Due to the tilting shaper spindle, the range of applications and savings of tooling cost may be much higher than you have expected. Using the handwheel causes the whole shaper spindle unit to tilt to the desired angle easily and smoothly.

The ”240“ shaper fence is standard equipment on the shaper units. The shaper fence can accomodate tooling to a maximum of 9“
(230 mm) and has a micro-adjustment on the shaper fence outfeed side. The integrated dust extraction cowling allows for chip removal. The spindle table opening is 9“ (230 mm). This allows the spindle with the cutterhead attached to be lowered below the table in some cases.

The MULTI fine adjustment system allows quick adjustment of the work piece diameter, allowing parallel guidance of the shaper fence.
- Automatic repeat setting after removal of your fence
- Parallel adjustments of the shaper fence
- Fence can be pre-set to a desired position
- Measurement scale for depth of cut

More than 50% of our clients now choose the electronic height adjustment for the sha­per spindle.

Optimize your cut­ting speed to suit each and every job. Infinitely variable speed control, from 1500–11,000 rpm.

The system cutterblock: 4-knife cutterblock, Quick and effortless knife change, Self-setting knives, therefore high accuracy when being changed, No resinous residue on the clamping screws, Extremely quiet operation due to the enclosed design, Standard or Tersa knife systems are also offered, Cost saving thanks to low price of planer blades

2 spring loaded pressure bars prevent “fluttering” of very thin workpieces during planing.

The highest accuracy is assured for standard ­shaping work and when using large cutters for tenoning with Felder shapers.

- Safety, since there is no pinch point
- No limitations on work piece height
- Power feeders may be used without problems
- Impeccable machined surface
- Optimal chip removal

“Power-Drive” gives you electronic height adjustment on the saw blade. Turn the control knob to adjust the blade height, displayed on a red LED display.