|
PRODUCTS
Machine Range
|
|
 |
|
|
|
|
|
MULTI fine adjustment system
The MULTI fine adjustment system allows quick adjustment of the work piece diameter, allowing parallel guidance of the shaper fence.
- Automatic repeat setting after removal of your fence
- Parallel adjustments of the shaper fence
- Fence can be pre-set to a desired position
- Measurement scale for depth of cut
|
|
|
High-Speed Router Spindle
Optional – replace the standard spindle with a 14,000 rpm router spindle (special order).
|
|
|
The renowned FELDER 500 saw assembly
Stable and compact saw unit built to last:
- Cutting height of 4” with a 12” (315 mm) blade
- Double-sided support
- Smooth tilting action 0°–45°
- Support close to the saw blade on both sides
|
|
|
Precision sliding table-Guiding system “X-Roll”.
“X-Roll”, making a difference:
- Extremely smooth and precise sliding action! With the roller-bearing system there is no single point of contact
between bearings and guiding track, maximizing precision over the lifetime of the machine.
- Clean, dust-free guide rails obtained by special wipers and brushes.
- Smooth movement of the sliding table ensured by hardened steel, ground-bearing tracks.
- 6-year-warranty
|
|
|
crosscut fence
The crosscut fence 51” (1300 mm) for crosscuts between +45° and –45°. The fence can be attached to the sliding table with out the use of tools. The end stop provides you with the exact 90° position.
|
|
|
Stop scale
The bevelled miter scale with hairline readout is visible from the operating area and thus allows exact reading of the required crosscut value.
|
|
|
Precision miter index system: accuracy in setting angles
The double miter system on the outrigger table with telescopic stop 102“ is standard for Professional models.
It’s exactly this feature that allows you to execute very accurate miter cuts from +45° to –45°, in a quick and easy way.
For those who want even more accurate settings, we equip the outrigger table with the ”precision miter index system.“ With this you can select predrilled positioning stops in steps of 5°, but also at 22.5°, by means of the index locating pin at the telescopic stop from +45° to –45°.
|
|
|
The renowned FELDER “500” Shaper assembly
Stable and compact spindle unit
for long lasting precision
- Maximum tooling above the table 4” (100 mm)
- Table opening 7" (180 mm)
- 4 speeds 3000, 6000, 8000, 10,000 rpm
- Collet chuck for high speed router spindle at 14,000 rpm
- Smooth reward tilt to 45°
- Height adjustment with cast iron segment
|
|
|
Multi-adjustment system for shaper fence “240”
Professional equipment: Shaper fence “240” for max. tooling diameter 9”, MULTI fine adjustment for shaper fence “240”
|
|
|
Tennoning and slotting
The highest accuracy is assured for standard shaping work and when using large cutters for tenoning with Felder shapers.
|
|
|
Tilt Bracket
The Felder device for tilting the feeder away means the power feeder always remains on the machine and can be used at any moment without problems.
|
|
|
Scoring unit
For the professional processing of sheet material the saw can be equipped with the independantly adjustable scoring unit.
|
|
|
rip fence
The rip fence is easily and smoothly adjustable, with a one-hand clamping mechanism.
The fine adjustment mechanism allows for precise measurements.
A rip capacity of 31½” (800 mm) comes standard with the option of upgrading to 49¼” (1250 mm). The rip scale is easy to read and perfectly integrated into the machine body.
|
|
|
The precision-fence “240”
The fence can house tooling of up to 9” with fine adjustment of the out-feed fence from –5 to +25 mm. The dust extraction is carried out via an integrate extraction port at the rear. The table open diameter is 7”, a huge advantage when working with large tooling below the table.
|
|
|
Tilting of the shaper spindle in the correct way on Felder “rearwards” with easy handling:
- Safety, since there is no pinch point
- No limitations on work piece height
- Power feeders may be used without problems
- Impeccable machined surface
- Optimal chip removal
|
|
|
to use a grooving cutter “Dado cutter”
The Felder 500 Series saw assembly is fully compatible with dado tooling. Thanks to a removable table insert and flanges, specialized Felder dado tooling can be used.
|
|
|
|
